DRO Project for Taig Lathe

vtcnc

Admin
Staff member
H-M Lifetime Diamond Member
Joined
Jun 29, 2014
Messages
4,051
I've wanted DRO for my Taig micro lathe for a few years now. I decided to roll the dice with iGaging scales and remote digital readouts. I've read mixed reviews, but the price is pretty low risk at about $85 for three 6" scales of eBay.

I snapped a few pics of the build and a final pic of the cross slide.

First, I needed to make a bracket to mount the scale to the carriage and the cross slide:

4c9723cbdd5a968046ab70c678295fba.jpg

Where I wanted to mount the bracket is tricky. There are four things to account for: the cross slide gib set screws, the carriage gib set screw locknut, the carriage gib itself and the carriage casting.

The draft angle on the back of casting was tricky, so I just filed that angle in by hand.

d6520bae72ba4d78a0317585dfac46fd.jpg

Also, watch your depth on the hole depth when you drill into the carriage, you don't want to drill into the carriage gib.

4153b5b9ef1f850582d254157ba809b8.jpg

Here is a photo of the tight squeeze:

14c2f30a724cac49a0ace9b66c9a053b.jpg

Once the bracket is on the carriage, you can mount the scale. I cut my scale down a few inches since it wouldn't fit between the lathe and back of my bench. The last thing to do is connect the cross slide to the scale. I used some 3/8 rod that sits in the right t-slot for perfect alignment. A coupled of holes later and the rod is connected to the scale:

4b896aded98d82b16402d34c9b86a8f5.jpg

Works great! I haven't tested it for accuracy yet, if all goes well, I'll move onto the next axis.

4c9723cbdd5a968046ab70c678295fba.jpg

4c9723cbdd5a968046ab70c678295fba.jpg

d6520bae72ba4d78a0317585dfac46fd.jpg

d6520bae72ba4d78a0317585dfac46fd.jpg

4153b5b9ef1f850582d254157ba809b8.jpg

4153b5b9ef1f850582d254157ba809b8.jpg

14c2f30a724cac49a0ace9b66c9a053b.jpg

14c2f30a724cac49a0ace9b66c9a053b.jpg

4b896aded98d82b16402d34c9b86a8f5.jpg

4b896aded98d82b16402d34c9b86a8f5.jpg
 
Nice job! You found a novel way to get around the problem of required room for the DRO read head, a real problem on those small machines. Thanks for sharing your solution, it will be inspiration for others I am sure.
 
Thanks. The only potential problem is fitting my top compound slide with that rod in the way. I will most likely make a bracket to mount off the back of the cross slide next.
 
Dang...I'm getting inconsistent measurements after testing the DRO setup today.

Backed the slide into the dial and zeroed the scale. Turned the dial until the readout said .500...measured with my Mitutoyo calipers...., and I get .525-.530. Tried it again and counted rotations, I definitely over rotated but the readout still claimed .500.

Went to iGaging website to see if there are any calibration routines for these readouts...nothing found. Does anybody have any advice here?
 
Could be electrical noise try grounding the lathe to the 110 ground wire. Also ground the motor frame to the power outlet if it is not already grounded. if you are using a VFD they generate quite a bit of electrical noise and VFD noise suppression gets a little more complicated.

Jim
 
Grounded the lathe tonight. That seemed to knock some noise out of the area. It seemed to cut the inaccuracy in half. I had a "duh" moment and realized that there felt like a bit too much backlash. Tightening things up took the inaccuracy from about .010" off to no more than .002". I can live with this. Thanks for the advice Jim!
 
Added the carriage readout today. Here is the final product...works great!
0b3fcd1391a456be420a55a4109d40b3.jpg

0b3fcd1391a456be420a55a4109d40b3.jpg

0b3fcd1391a456be420a55a4109d40b3.jpg
 
I couldn't leave well enough alone. During my research on scale calibration for this project, I ran across this website: http://www.yuriystoys.com

I ran to Radio Shack and grabbed the needed components. About 4-5 hrs later, I'm pleased to say that I now have not only DRO on my Taig lathe, but wireless DRO using my Nexus 7 as the display!! Amazingly, my first Arduino project worked the first try, I fully expected soldering and pin problems. No problems! I need to calibrate next. The Android app is called TouchDRO and it switches from lathe to mill using the device's Bluetooth connection.

When people say "what a weird world we live in"...it is these small examples of technology that make me marvel at what a fantastic world we live in where anybody can do this!

In the pic below you can see the extra enclosure containing the Arduino and SeeedProtoshield. My Android Nexus 7 is up on the board with full touchscreen controls. Even let's you add tool library!

0e34feee24a66ca997ae10a1b68efc64.jpg

Next photo is a bench test of the board connected to a scale. Worked first time...still can't believe it

af99b9ed7fda30da9a9265d90d49704e.jpg

And a shot of Arduino before it gets sealed up...

47e2ab7ca11d2698c4a409855ea55fd0.jpg

0e34feee24a66ca997ae10a1b68efc64.jpg

0e34feee24a66ca997ae10a1b68efc64.jpg

af99b9ed7fda30da9a9265d90d49704e.jpg

af99b9ed7fda30da9a9265d90d49704e.jpg

47e2ab7ca11d2698c4a409855ea55fd0.jpg

47e2ab7ca11d2698c4a409855ea55fd0.jpg
 
Great work I love when you can find a new way to creat solutions to projects!
 
Back
Top