A view of the spindle speed change plate installed.

A view of the spindle speed change plate installed.

  • Reaction score 0
  • Comments 0
The two mounting holes for the speed change face plate.

The two mounting holes for the speed change face plate.

  • Reaction score 0
  • Comments 0
After the two screws are installed that hold the speed change assembly on the belt housing.

After the two screws are installed that hold the speed change assembly on the belt housing.

  • Reaction score 0
  • Comments 0
The speed change assembly is held on the belt housing by two socket head screws that go here.

The speed change assembly is held on the belt housing by two socket head screws that go here.

  • Reaction score 0
  • Comments 0
The spindle speed change plate. The long screws hold the speed change assembly on to the belt housing. The little screws hold the face plate on.

The spindle speed change plate. The long screws hold the speed change assembly on to the belt housing. The little screws hold the face plate on.

  • Reaction score 0
  • Comments 0
Tighten the 3 cap screws down and you've installed the bearing cap. Next!

Tighten the 3 cap screws down and you've installed the bearing cap. Next!

  • Reaction score 0
  • Comments 0
Another view of where you install the bearing cap screws.

Another view of where you install the bearing cap screws.

  • Reaction score 0
  • Comments 0
Install the 3 cap head scres like so. The other three holes in the cap are used for removing a stuck cap.

Install the 3 cap head scres like so. The other three holes in the cap are used for removing a stuck cap.

  • Reaction score 0
  • Comments 0
I had put witness marks when I removed the bearing cap. If you did make sure to line them up.

I had put witness marks when I removed the bearing cap. If you did make sure to line them up.

  • Reaction score 0
  • Comments 0
Place the bearing cap over the bearing and the wavy spring washer.

Place the bearing cap over the bearing and the wavy spring washer.

  • Reaction score 0
  • Comments 0
Set the wavy spring washer on top of the bearing.

Set the wavy spring washer on top of the bearing.

  • Reaction score 0
  • Comments 0
Side view of wavy spring washer...new wavy spring washer.

Side view of wavy spring washer...new wavy spring washer.

  • Reaction score 0
  • Comments 0
Next up bearing cap installation. You'll need what you see here. Bearing cap, 3 cap screws, and the wavy spring washer...

Next up bearing cap installation. You'll need what you see here. Bearing cap, 3 cap screws, and the wavy spring washer...

  • Reaction score 0
  • Comments 0
Another top down view of the speed plate screws showing the space around the pivot sleeve.

Another top down view of the speed plate screws showing the space around the pivot sleeve.

  • Reaction score 0
  • Comments 0
How it'll look after you install the speed change plate screws with pivot sleeves. They will have space around them.

How it'll look after you install the speed change plate screws with pivot sleeves. They will have space around them.

  • Reaction score 0
  • Comments 0
Here you can see the speed change plate holes lined up with the sliding bearing housing.

Here you can see the speed change plate holes lined up with the sliding bearing housing.

  • Reaction score 0
  • Comments 0
Use these two screws with the pivot sleeves to mount the speed change plate to the sliding bearing housing.

Use these two screws with the pivot sleeves to mount the speed change plate to the sliding bearing housing.

  • Reaction score 0
  • Comments 0
The other two shorter cap screws go here. This will mount the upper belt housing to the lower belt housing. Only a few more steps to go!

The other two shorter cap screws go here. This will mount the upper belt housing to the lower belt housing. Only a few more steps to go!

  • Reaction score 0
  • Comments 0
The two long cap head screws go here.

The two long cap head screws go here.

  • Reaction score 0
  • Comments 0
These are the 4 cap screws you'll use to attach the upper belt housing to the lower belt housing.

These are the 4 cap screws you'll use to attach the upper belt housing to the lower belt housing.

  • Reaction score 0
  • Comments 0
Just in case you forgot we are going to take this rebuilt upper belt housing...flip it over and place it on top of the Lower belt housing.

Just in case you forgot we are going to take this rebuilt upper belt housing...flip it over and place it on top of the Lower belt housing.

  • Reaction score 0
  • Comments 0
Use the other 2 cap screws here to finish securing the lower belt housing to the heaad unit. These are on the front.

Use the other 2 cap screws here to finish securing the lower belt housing to the heaad unit. These are on the front.

  • Reaction score 0
  • Comments 0
Use 2 of the cap screws here. These two holes are in the back.

Use 2 of the cap screws here. These two holes are in the back.

  • Reaction score 0
  • Comments 0
The four cap screws you will need to mount the lower belt housing to the head unit.

The four cap screws you will need to mount the lower belt housing to the head unit.

  • Reaction score 0
  • Comments 0
expressline99

Bridgeport Series 1 VS 2hp reinstalling lower/upper belt housing on the head

Reinstalling the rebuilt lower and upper belt housing back on the head.
Click to expand...

Album information

Album owner
expressline99
Date created
Item count
29
View count
8,917
Comment count
0
Rating
0.00 star(s) 0 ratings

Album privacy

expressline99

expressline99

Media items
1,002
Albums
19
Can view media items
Everyone
Can add media items
Album owner only

Share this album

Back
Top