Can acetone be used to clean any precision tools?

O

ome

Forum Guest
Register Today
I bought quite a few beautiful precision tools and want to care for them properly.
My planer gage has a small amount of rust on the slider along the way, what is the appropriate procedure for getting rid of the rust?
 
acetone can damiage plastics and paint so you have to be real carfull with it. As for the rust I use 0000 steal wool and some PB blaster.
 
Hello there,

Acetone can be used to clean almost all of your machine surfaces. Note that I said MACHINE surfaces. Bare steel, or cast will not be damaged by acetone, but be sure to lubricate them again when you are done. However, you have to use caution with acetone, as it is GREAT at removing paint! Like the paint found in the markings on most precision tools.

About the rust on your planer gauge. Acetone will not help you here. It will only make very clean rust. If the rust is just surface rust, you are better off getting some fine steel wool, or very fine sandpaper and gently polish the rust off. If it is more severe, try a product called "Evap-o-rust". It has been used successfully by many forum members, including myself, to remove even the deepest most set in rust. Let the part soak for a couple of hours, brush with a brass brush, and any sign of rust will disappear. Well except for the pitting.

-Cody
 
I agree with using a chemical removal method for rust. Any mechanical means, no matter how fine will leave permanent scratches. Just run down to your local automotive paint supply and ask for metal prep. It's a mild phosphoric acid based cleaner that will remove light rust without damaging the surface. It is water based though, so the tools will need to be dried and oiled after you use it.

Tom
 
One thought about this -and it's a general consideration not specific to Acetone... Be very careful with all chemicals if you intend to weld the part. Residual amounts of brake cleaner will kill you (or leave you a vegetable) when hit with high heat from welding. This is not an urban legend -it's a fact.

I don't specifically know if Acetone has this problem but, I avoid all things similar to it, naptha etc... I stick to plain old isopropyl alcohol (rubbing alcohol) in higher concentrations at 80% or greater for virtually all of my cleaning/degreasing and it works very, very well -and it's cheap.

As a side note, galvanized metals can poison you as well. In general, be careful what you work with and take precautions when working with unknown metals.

-Sorry for the OT post but, this seemed like a good time to remind folks.

Ray
 
Ray,

It's the chlorinated solvents contained in brake cleaner, paint remover and some tapping fluids (trichloroethylene) exposed to the UV radiation in gas shielded arc welding that can under certain conditions produce deadly phosgene gas. Common solvents like naptha, acetone and mineral spirits are fine. Just make sure everything you weld is completely dry.

Tom
 
One thought about this -and it's a general consideration not specific to Acetone... Be very careful with all chemicals if you intend to weld the part. Residual amounts of brake cleaner will kill you (or leave you a vegetable) when hit with high heat from welding. This is not an urban legend -it's a fact.

I don't specifically know if Acetone has this problem but, I avoid all things similar to it, naptha etc... I stick to plain old isopropyl alcohol (rubbing alcohol) in higher concentrations at 80% or greater for virtually all of my cleaning/degreasing and it works very, very well -and it's cheap.

As a side note, galvanized metals can poison you as well. In general, be careful what you work with and take precautions when working with unknown metals.

-Sorry for the OT post but, this seemed like a good time to remind folks.

Ray
Thank You for that warning, but I do not at this time, know how to weld..
 
Although it is a GRAS, it still pays to be familiar with all substances used in your shop. Acetone is a good choice for degreasing and cleaning, but of course, there are caveats. I have worked around it a good deal in a laboratory environment as well as a machine shop. I keep at least a gallon on hand at any time. Unfortunately, purchase of it in some areas has come under scrutiny because of the potential use in manufacturing methamphetamine. The cost has gone up a bit in the last couple of years, but Lowe's and Home Depot still carry it.

Please read about it here:

http://en.wikipedia.org/wiki/Acetone

And it might be a good idea to keep the MSDS on hand for reference also:

http://www.sciencelab.com/msds.php?msdsId=9927062

It's probably best to get the MSDS from the manufacturer of the brand you purchase from their website. They are legally required to make it available. The one I gave will suffice if you don't care to track down the one from your manufacturer.
 
Be very careful with all chemicals if you intend to weld the part. Residual amounts of brake cleaner will kill you (or leave you a vegetable) when hit with high heat from welding. This is not an urban legend -it's a fact.

It's the chlorinated solvents contained in brake cleaner, paint remover and some tapping fluids (trichloroethylene) exposed to the UV radiation in gas shielded arc welding that can under certain conditions produce deadly phosgene gas. Common solvents like naptha, acetone and mineral spirits are fine. Just make sure everything you weld is completely dry.

Any halogen (chlorinated, fluorinated, brominated, etc.) solvents or refrigerants all when exposed to hot metal surfaces (not UV radiation) can and will produce very toxic gases, phosgene in only one of them, not only should you make sure the part are not only dry but the welding area is well ventilated as well. Generally any Non-flammable solvents are halogenated. Flammable solvents generally are free of halogens. As stated acetone will not damage any metal surfaces but be careful around paint and polymers.
 
Back
Top