Jet 1336 spindle removal help needed

yooper

Registered
Registered
Joined
Jul 8, 2013
Messages
35
My dad called me to look at his jet lathe because it was making a noise. I tracked it down to what I think is in the spindle bearings. The noise is a steady clunking sound, that goes away when I push on the spindle with a block of wood. I need to find out how the piece that the chuck screws on to can be removed. Also any advise on how to remove the spindle.

Thanks Rick
 
A sound like that could be the pin that locks it in high gear.
Make certain the pin is released and is firmly seated in the mating hole unless your running in back gear.
If your running in back gear then make certain the pin is raised and captured so it can't ride on the spindle and bounce over the mating hole.
I'm assuming your lathe isn't a gear head machine.

Jim
 
A sound like that could be the pin that locks it in high gear.
Make certain the pin is released and is firmly seated in the mating hole unless your running in back gear.
If your running in back gear then make certain the pin is raised and captured so it can't ride on the spindle and bounce over the mating hole.
I'm assuming your lathe isn't a gear head machine.

Jim

I already checked the pin and that isn't the problem. When I push up on the spindle with a block of wood the noise goes away. We have the left side loose but need to get the right side loose so we can get the spindle out.

Thanks for the advice.

Rick
 
my first thought was the bearing preload seems to have been lost.
were any locking collars or locknuts loose on the spindle?
does the sound get worse as he operates?
i'm assuming he's kept oil in the bearing reservoirs and the clunking is not caused by a lack of lubrication.

from what i have seen and read,you remove, spindle locknut and retainer, the chuck, and bearing retainer & set screws and spindle set screws the spindle comes out towards the bed.
i have read that a man made a custom puller that went through the spindle kinda like a reverse collet closer, that draws the spindle out from the headstock using allthread and some nuts and a couple fabricated collars.

i imagine you could be a little more cro-magnon and use soft materials (lead,brass,wood,aluminum, etc) to use as a drift to drive the spindle out (being careful not to damage spindle or threads of course).

i hope the information helps out!
 
Last edited:
Ulma Doctor. It is possible that he lost the preload, however he tried to take it apart before he called me for help. I have the lock nuts and the pulleys loose except for the one closest to the bed. I can see that one has a key slot in it and it slides with the shaft up to the casting and I don't want to break the casting. I will check to see if I can make a puller of some sort the next time I head down there. Its a 25 or 30 year old machine and I am not sure if he kept an eye on the lubrication level. I do know that we need a new o-ring for the spindle - oops on my part. I will keep you posted and maybe try to learn how to post pics.
 
Ulma Doctor. It is possible that he lost the preload, however he tried to take it apart before he called me for help. I have the lock nuts and the pulleys loose except for the one closest to the bed. I can see that one has a key slot in it and it slides with the shaft up to the casting and I don't want to break the casting. I will check to see if I can make a puller of some sort the next time I head down there. Its a 25 or 30 year old machine and I am not sure if he kept an eye on the lubrication level. I do know that we need a new o-ring for the spindle - oops on my part. I will keep you posted and maybe try to learn how to post pics.

Is it a belt drive that looks like this one?

jet-002.jpg

jet-001-e1380048676625.jpg

jet-002.jpg jet-001-e1380048676625.jpg
 
Yes it looks very similar, his is a BD-1336 , Stock number 321345, Probably the same machine.
 
Yooper,
Did you succeed in removing your spindle? I'm working on removing mine (Jet 1336 PBD) right now and if you have any suggestions, I would appreciate them. Did you tap it out or pull it with a piece of all-thread? Did you happen to take any pictures?
 
Back
Top