Machine leveling

Richard S

Registered
Registered
Joined
Jun 29, 2017
Messages
5
I've just joined the Forum, this is my first post. I just bought a used 920 jet lathe. The manual for it that I've downloaded indicates that it should be leveled or the stand(which I have) should be bolted to the floor. Elsewhere I have read the lathe bed May twist if this procedure is not followed.
I found no discussion of this topic when I searched hobby Machinist and see no evidence in pictures of casually placed machines. I've shimmed the machine so all four feet share the load of the lathe but I'm loathe to Bolt the machine in place--dedicated space being at a premium.
 
Hi Richard, welcome. I agree the search capabilities on the forum can sometimes lathe a bit of functionality, but I just did a quick forum search using "lathe levelling" and found two pages of threads on the topic. It is a frequently discussed subject here and I'm sure there will be many replies, but in the meantime this may give you a few older posts to look at.

-frank
 
I've just joined the Forum, this is my first post. I just bought a used 920 jet lathe. The manual for it that I've downloaded indicates that it should be leveled or the stand(which I have) should be bolted to the floor. Elsewhere I have read the lathe bed May twist if this procedure is not followed.
I found no discussion of this topic when I searched hobby Machinist and see no evidence in pictures of casually placed machines. I've shimmed the machine so all four feet share the load of the lathe but I'm loathe to Bolt the machine in place--dedicated space being at a premium.

Bolting the stand to the floor accomplishes two things. It prevents the stand from moving during use and it tends to stabilize the stand and lathe blessing the possibility of your previously adjusted lathe losing its adjustment. This is more important on a light stand/lathe is unintentional shift in position is more likely. However, there are many lathe setups where the lathe is free standing. My lathes are set on heavy stands which are not easily moved and are free standing.

Leveling a lathe is important to prevent twisting of the bed. A twisted bed will turn a taper on a cylinder because the cutting surface is rotated towards or away from the spindle axis. A left hand twist will rotate the tool into the spindle as you move towards the tailstock, causing a smaller turned diameter at that end. Sometimes twist is intentionally added to correct for a non-level condition. It is preferable to level the lathe as best you can before using any twist. Leveling precisely requires a machinist's level with sensitivities in the .005"/ft to .0005"/ft range. This is far more sensitive than a typical carpenter's level. Since these levels are fairly expensive, most hobbyists use a two collar test or procedure known as Rollie's Dad's Method to determine correct alignment.

The two collar test basically involves turning an area on a cylinder near the headstock and one near the tailstock. If the lathe is aligned, the two diameters will be equal. The RDM method uses a bar of uniform roundness and diameter along with a suitable indicator to measure the distance to the spindle axis near the headstock and near the tailstock. It involves some simple calculations but turning isn't required and the bar doesn't have to be free from runout. Note that the bar isn't supported in the tailstock in either of these tests. For that reason, a fairly stout bar to minimize deflection is required.
 
I appreciate the input guys. I'm awaiting the arrival of a dial indicator so it looks like I can proceed.

I still find myself hesitating to bolt it down and dedicate the space permanently. In the past I have grouted heavy equipment in place and I wonder if I could get away with that here here. This 920 with its base is just shy of 300 lb.
 
Richard, I have noticed two basic camps on this subject. One group says you should mount the stand on a solid footing, like concrete, and bolt it down. Clearly, this is the ideal but to say it is the only way - no, it's not.

The second group are guys with small shops who have to move the lathe from time to time. For this purpose, leveling casters like Foot Master, Carry Master and others are popular. While not ideal, sometimes you just have to move the lathe and casters allow that. I use this method and have to re-level the lathe when I re-site it and it can be either fast or agony, depending on the Universe's sense of humor on that day. A good precision level helps.

Yet another group mounts their lathe on a rolling tool chest; I suppose they're a sub-group of the first camp. Most of these guys obviously have small lathes like your 9 X 20. Moving the tool chest does not disturb the level of the lathe so you might consider this. If you go this route, make sure the surface you mount the lathe on is solid and unmoving and you should be okay. We were just discussing this in this thread:

http://www.hobby-machinist.com/thre...put-under-a-benchtop-lathe.60245/#post-496728

Good luck, whichever way you decide to go.
 
There is a very small minority that don't worry about leveling their lathe, I do no work longer than 3 or 4 inches long in my lathe, and have the tailstock adjusted for almost no taper. If I need better I achieve it with paper or file. It's a small lathe, 6 by 20, flat ways, on a wooden stand. No wheels, no leveling feet.
 
With a lathe that small it comes down to the bed rigidity. If the lathe on the stand cuts with no or tolerable taper then leave it alone. If not then it will need to be leveled to correct that. Sometimes, such as my 13x40 it is on leveling screws but no hold downs to the floor. It is level to my Starrett 12 in machinists level and cuts 0/0 over 12".
 
I appreciate all the responses. I'm somewhat reassured that if I proceed to check for level, I can determine how rigid the Lathe bed and base are. Starting out I don't anticipate turning long pieces.
With a lathe that small it comes down to the bed rigidity. If the lathe on the stand cuts with no or tolerable taper then leave it alone. If not then it will need to be leveled to correct that. Sometimes, such as my 13x40 it is on leveling screws but no hold downs to the floor. It is level to my Starrett 12 in machinists level and cuts 0/0 over 12".
 
I appreciate all the responses. I'm somewhat reassured that if I proceed to check for level, I can determine how rigid the Lathe bed and base are. Starting out I don't anticipate turning long pieces.

Richard, leveling the lathe tells you nothing about rigidity. It only tells you if the lathe is level or not relative to how the lathe is mounted or sited. After leveling, you usually will either take measurements or take very fine test cuts on a 2-collar bar; this allows you to fine tune and/or confirm that the lathe is level.

Rigidity is a whole other thing.
 
Back
Top