new SuperMax 30taper --Needs a drawbar or power drawbar

countryguy

Active User
Registered
Joined
May 7, 2014
Messages
776
Hi everyone, Been burning up the forum on the new Mill. It's in the Garage now and I've started to dig in on her. I see that it has no drawbar or power drawbar. The manual notes it's a NST 30 7/24 (or NMTB right?).

So here is the question. Power drawbars seem pretty cheap. But what kind/type? Will a BPclone type work? there is a mounting top (pic below).

There is also this Pnumatic actuator or some kind on the side (see pics).... And I'm unclear what that is really for?

so- Can ya'll help me find a powerdraw bar setup? Maybe even a tool changer for a Supermax (would be sweet!) really... Do they exist :)
Short-term - What do I get just to have a manual drawbar. Is this just a threaded rod with a bolt top like my manual R8 Dbar?

thanks everyone!
drawbar1.jpg30taper1.jpg

drawbar1.jpg 30taper1.jpg
 
Last edited:
You can build a drawbar just like a BP type. I'm pretty sure the NMBT 30 tooling is a 1/2-13 thread. I would get a length of Grade 8 allthread and make it out of that.

As far as the pneumatic cyl, back gear shift maybe?
 
OK.. 1/2 13 is correct Jim. Thanks as Always!! Grade 8 allthread, McMasterCarr or my local Production Tool Supply place. Not an Enco, but very close and always a great Clearance table!

OK, So I see these are really fun projects! power drawbar...Yeah, I can do that. Fun Fun Fun.
http://www.cnccookbook.com/CCMillDrawbar.html
 
I built my own power drawbar many moons ago...

Looks similar to the one you found except I used an electric impact wrench.

Karl
 
Parts lists: SuperMax 30taper --Needs a drawbar or power drawbar

OK, Updating w/ equipment for other Newbs in the Ether that buy a Mill and need to make it all go again ;-)

30 Taper- Uses 12-13 as we've said above.

1) Drawbars can be found from ToolGuy2 on ebay. large selection and noted good review. Here is mine for a SuperMax YCM style .
http://www.ebay.com/itm/300332912464

2) Power unit ( so many... Here is a good link which I bought. )
http://www.ebay.com/itm/111393959683 I actually talked to Todd. Cool guy and willing to take Q&A directly. Cannot ask for better!

3) Knee crank... We'll , I saw this and simply could not say no.
http://www.ebay.com/itm/300864598720


Thus ends the saga of no tool holder mounting. No to dig up the tool holders themselves.
Have a wonderful 2015 all!
Jeff / CG.
 
Hi everyone, Been burning up the forum on the new Mill. It's in the Garage now and I've started to dig in on her. I see that it has no drawbar or power drawbar. The manual notes it's a NST 30 7/24 (or NMTB right?).

So here is the question. Power drawbars seem pretty cheap. But what kind/type? Will a BPclone type work? there is a mounting top (pic below).

There is also this Pnumatic actuator or some kind on the side (see pics).... And I'm unclear what that is really for?

so- Can ya'll help me find a powerdraw bar setup? Maybe even a tool changer for a Supermax (would be sweet!) really... Do they exist :)
Short-term - What do I get just to have a manual drawbar. Is this just a threaded rod with a bolt top like my manual R8 Dbar?

thanks everyone!
View attachment 90742View attachment 90743

It appears that the spindle nose keys are missing, and the screws that held them on have been broken off; you will need to replace them to drive the adaptors that you buy. As far as a drawbar is concerned, I would machine one from scratch with a larger diameter upper end to engage the hole at the top, and extend it about 3 or 4 inches above the top of the head, and mill flats at the top about 3/4 or 1"long and 7/8 across the flats (standard size for a 1/2" extra heavy nut) Unless you plan to do a crazy amount of tool changing, a power drawbar is unnecessary.
 
My super max has this cylinder it is a spindle brake it engages just for a moment when stop is depressed. But this is an older thread and I bet you know this now.
 
Back
Top