Refurbing A Found Union Mfg Precision Vise.

astroracer

Registered
Registered
Joined
Apr 1, 2015
Messages
76
I found this vice Friday at a big indoor antique mall near Flint. $35 bucks to much?
MVC014F-vi.jpg
The clamp jaw was rusted pretty solid and the whole thing was pretty crusty but I saw potential...
MVC013F-vi.jpg
It took a couple of hours today to get the slide loosened up and removed. You can see where it was sitting. :)
MVC011F2-vi.jpg
I used a bunch of steel cutoffs and a wedge to get it apart.
MVC003F-vi.jpg
With everything stripped off it was time to start refinishing. The bottom of the slide was nasty...
MVC012F2-vi.jpg

MVC014F-vi.jpg

MVC013F-vi.jpg

MVC011F2-vi.jpg

MVC003F-vi.jpg

MVC012F2-vi.jpg

MVC014F-vi.jpg

MVC013F-vi.jpg

MVC011F2-vi.jpg

MVC003F-vi.jpg

MVC012F2-vi.jpg

MVC014F-vi.jpg

MVC013F-vi.jpg

MVC011F2-vi.jpg

MVC003F-vi.jpg

MVC012F2-vi.jpg

MVC014F-vi.jpg

MVC013F-vi.jpg

MVC011F2-vi.jpg

MVC003F-vi.jpg

MVC012F2-vi.jpg

MVC014F-vi.jpg

MVC013F-vi.jpg

MVC011F2-vi.jpg

MVC003F-vi.jpg

MVC012F2-vi.jpg
 
The process I used to clean this up was to soak the parts in Simple Green for 15 or 20 minutes then scrub the parts with ScotchBrite and a toothbrush to degrease them.
After degreasing I hit most everything with a flap wheel on the 4" grinder to knock off all of the big rust.
Then I soaked everything in Metal Ready to remove the left over rust and get the parts ready for Black Oxide.
MVC001F-vi.jpg
Starting the Black Oxide dip.
MVC015F2-vi.jpg
This went pretty quick once I got the thing apart... Everything is Black Oxided and sealed.
MVC015F3-vi.jpg

MVC011F3-vi.jpg

MVC008F2-vi.jpg
I wire brushed and Metal Readied the handle to get it ready for paint. I sprayed it flat black to sort of match the rest of the body. That will be the only thing I have to finish tomorrow. I will spray a couple of heavy coats of matte clear on it to seal it up.
It's still wet in the pic.
MVC005F2-vi.jpg
I'll post up pics after asm tomorrow.
Mark

MVC001F-vi.jpg

MVC015F2-vi.jpg

MVC015F3-vi.jpg

MVC011F3-vi.jpg

MVC008F2-vi.jpg

MVC005F2-vi.jpg

MVC001F-vi.jpg

MVC015F2-vi.jpg

MVC015F3-vi.jpg

MVC011F3-vi.jpg

MVC008F2-vi.jpg

MVC005F2-vi.jpg

MVC001F-vi.jpg

MVC015F2-vi.jpg

MVC015F3-vi.jpg

MVC011F3-vi.jpg

MVC008F2-vi.jpg

MVC005F2-vi.jpg

MVC001F-vi.jpg

MVC015F2-vi.jpg

MVC015F3-vi.jpg

MVC011F3-vi.jpg

MVC008F2-vi.jpg

MVC005F2-vi.jpg

MVC001F-vi.jpg

MVC015F2-vi.jpg

MVC015F3-vi.jpg

MVC011F3-vi.jpg

MVC008F2-vi.jpg

MVC005F2-vi.jpg
 
Not only is your presentation top notch, your vice is unusual. It appears to be an adjustable quick lock vise used for production. Put the part in, located against a stop (not present, or built into the interchangeable jaw inserts) clamp, preform the operation, (drill, tap, mill, grind, whatever) open, remove part, insert new part, clamp release.
That would be a nice vice to have for short runs.

Nice find.
 
I hope you didn't use the flap disk on the sliding surfaces. The phosphoric acid would have removed all the rust (though it's quicker if you wire-brush the scale off).
 
That would be a great addition to any metal shop.
Great thread pics. Thanks for sharing.
 
Obviously, you paid too much. But don't worry; I'm such a nice guy, I'll give you $40!
 
I hope you didn't use the flap disk on the sliding surfaces. The phosphoric acid would have removed all the rust (though it's quicker if you wire-brush the scale off).
Hi John, no flap wheel on the sliding surfaces. Actually I scrapped those a bit before the acid bath. There was a lot of build up and it needed to come off. Especially around the slide where it was rusted down. I have it together now and it works great! I'll post up some pics later after I get them loaded.
Mark
Hi Mike, just saw your offer... I knew 35 was a bit much but now I have about 10 hours of work into this thing so I would have to ask at least 45... Sorry. :)
 
I just noticed i never posted pics of the finished vise.
Here they are you wouldn't even recognize it from it's former sadness...
When I brought it home Friday afternoon...
MVC014F-vi.jpg
And two days later. All cleaned up and fully useable!
MVC021F-vi.jpg
It went back together easily and the slide NOW works as it is supposed too. It does take some effort, which is good, as that means it is still pretty tight. This is a very fine addition to my collection.
MVC019F-vi.jpg

MVC020F-vi.jpg
Thanks for looking.
Mark

MVC014F-vi.jpg

MVC021F-vi.jpg

MVC019F-vi.jpg

MVC020F-vi.jpg

MVC014F-vi.jpg

MVC021F-vi.jpg

MVC019F-vi.jpg

MVC020F-vi.jpg
 
Great job on the restoration Mark. Always nice to see an old, neglected tool brought back to life, and put back to work. Let us know how it works out on the mill. Cheers, Mike
 
Back
Top