T
TOOLMASTER
Forum Guest
Register Today
made some game board pieces before..fun not having specs to go by.
what is the od?
what is the od?
-
Welcome back Guest! Did you know you can mentor other members here at H-M? If not, please check out our Relaunch of Hobby Machinist Mentoring Program!
2016 POTD Thread Archive
- Thread starter sanddan
- Start date
- Joined
- Jul 12, 2015
- Messages
- 287
Good idea. Nice!
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
- Joined
- Nov 2, 2015
- Messages
- 12
23.52mm w. X 21.71 sorry for no banana for scale.
Sent from my XT1097 using Tapatalk
- Joined
- Aug 26, 2013
- Messages
- 1,061
I thought I posted the video a while back, but I couldn't find it, so he is a link to it.
I may have the solution to loading photos upside down. For months all my photos load on here upside down or sideways they are correct on my phone and on my computer but not on here. Someone on here told me to edit them first. I take my photos in the shop with my phone and download them to my computer. They look OK but don't load right here. If I open the edit feature on my phone and select crop. and then just crop a tiny bit or what I want and then save them, next download to the computer , they load here correctly. don't know why, don't care why, it works. ( it has something to do with the way the phones format the photos when taken). I also find after editing, they download correctly from the phone to here.
- Joined
- Apr 21, 2015
- Messages
- 894
I inherited a neglected surface grinder one year ago. I only made it as far as cleaning it up before life and other projects took over. Today I finally wired up a power switch (power cord was the switch) and mostly dressed the permanent magnetic chuck.
I forgot to take a picture of the before, but believe me when I say that it was badly rusted. I first indicated it to see how bad it was. I only have a dial travel indicator, not a test indicator. It showed a range of almost 0.004". So not good.
Then I saturated it with WD-40 and lightly stoned the entire surface. That brought it down to about 0.002". Still more than I would like to have to remove, but I suppose it could be worse. Here it is after the first pass with a freshly dressed wheel.
As you can see it's higher at the near side than the far. I thought I had it very clean before I mounted it. Not going to worry about it now. Just running with it.
After the second pass:
Taking very light passes to avoid heating it up. Also misting with water to keep it cool. Forgot to do a shot after the third pass. Here's the fourth:
Eventually I remembered to engage the magnet while running it. Fifth and final pass tonight:
I had to stop because it was getting late, I hadn't seen my wife much today, and I have an early dentist appointment. Tomorrow night I will take one more of these rough passes, then re-dress the wheel and take a final tenth with smaller steps and going both directions before advancing.
Hard to get a clean shot with one hand, in waning light, while cranking, but here's an obligatory sparky shot. (The long shutter speed makes it look like a much heavier grind than it actually was.)
I forgot to take a picture of the before, but believe me when I say that it was badly rusted. I first indicated it to see how bad it was. I only have a dial travel indicator, not a test indicator. It showed a range of almost 0.004". So not good.
Then I saturated it with WD-40 and lightly stoned the entire surface. That brought it down to about 0.002". Still more than I would like to have to remove, but I suppose it could be worse. Here it is after the first pass with a freshly dressed wheel.
As you can see it's higher at the near side than the far. I thought I had it very clean before I mounted it. Not going to worry about it now. Just running with it.
After the second pass:
Taking very light passes to avoid heating it up. Also misting with water to keep it cool. Forgot to do a shot after the third pass. Here's the fourth:
Eventually I remembered to engage the magnet while running it. Fifth and final pass tonight:
I had to stop because it was getting late, I hadn't seen my wife much today, and I have an early dentist appointment. Tomorrow night I will take one more of these rough passes, then re-dress the wheel and take a final tenth with smaller steps and going both directions before advancing.
Hard to get a clean shot with one hand, in waning light, while cranking, but here's an obligatory sparky shot. (The long shutter speed makes it look like a much heavier grind than it actually was.)
F
Firestopper
Forum Guest
Register Today
I may have the solution to loading photos upside down. For months all my photos load on here upside down or sideways they are correct on my phone and on my computer but not on here. Someone on here told me to edit them first. I take my photos in the shop with my phone and download them to my computer. They look OK but don't load right here. If I open the edit feature on my phone and select crop. and then just crop a tiny bit or what I want and then save them, next download to the computer , they load here correctly. don't know why, don't care why, it works. ( it has something to do with the way the phones format the photos when taken). I also find after editing, they download correctly from the phone to here.
Thanks for the advice Mark, I'll give it a try.
Update, I did exactly what you recommended and it worked!
Last edited by a moderator:
- Joined
- Apr 21, 2015
- Messages
- 894
When you take a photo with a phone or a camera it records the data from the sensor and includes a tag (think of it like a post-it note on the outside of.the file) with instructions about which way to orient the image when you look at it. Some software (including my local classified site; almost no one uses craigslist around here) gets confused by the tag from some cameras and phones. But when you edit the file in any way it saves the image in the correct orientation and omits the orientation flag. Problem solved-ish. Avoided, anyway.
Sent from my SPH-L300 using Tapatalk
Sent from my SPH-L300 using Tapatalk
- Joined
- Dec 27, 2014
- Messages
- 4,059
We have to assume you cleaned the surfaces between the magnet and the table before grinding the top.