View of the motor and high low speed switch installed.

View of the motor and high low speed switch installed.

  • Reaction score 0
  • Comments 0
Remount the high low switch with the two flat head screws it had...if you haven't lost them yet.

Remount the high low switch with the two flat head screws it had...if you haven't lost them yet.

  • Reaction score 0
  • Comments 0
This is where you install the high speed low speed switch. Left side of the belt housing if you are looking at it from the front of the machine.

This is where you install the high speed low speed switch. Left side of the belt housing if you are looking at it from the front of the machine.

  • Reaction score 0
  • Comments 0
The installed junction box on the motor.

The installed junction box on the motor.

  • Reaction score 0
  • Comments 0
Part numbers inside of the junction box cover.

Part numbers inside of the junction box cover.

  • Reaction score 0
  • Comments 0
The junction box cover with screws.

The junction box cover with screws.

  • Reaction score 0
  • Comments 0
These are the wire groupings for connecting your motor wiring to the high and low speed switch.

These are the wire groupings for connecting your motor wiring to the high and low speed switch.

  • Reaction score 0
  • Comments 0
Mounting location on the motor for the junction box. It's three phase so it has 9 wires.

Mounting location on the motor for the junction box. It's three phase so it has 9 wires.

  • Reaction score 0
  • Comments 0
Back of the high and low speed switch.

Back of the high and low speed switch.

  • Reaction score 0
  • Comments 0
High and low speed switch.

High and low speed switch.

  • Reaction score 0
  • Comments 0
The electrical junction box that mounts on the motor with cover plate and screws..mounting bolts.

The electrical junction box that mounts on the motor with cover plate and screws..mounting bolts.

  • Reaction score 0
  • Comments 0
The installed motor pulley access plate....yeah I polished mine and the finish looks awful in the picture. Looks much better in person!

The installed motor pulley access plate....yeah I polished mine and the finish looks awful in the picture. Looks much better in person!

  • Reaction score 0
  • Comments 0
You can install the motor pulley access plate with the three screws here now. :)

You can install the motor pulley access plate with the three screws here now. :)

  • Reaction score 0
  • Comments 0
Motor pulley access plate with socket head screws.

Motor pulley access plate with socket head screws.

  • Reaction score 0
  • Comments 0
view of the motor shaft installed through the variable disk assembly Held in place with a snap ring.

view of the motor shaft installed through the variable disk assembly Held in place with a snap ring.

  • Reaction score 0
  • Comments 0
At this point you have to wrestle the motor on and line up the keyway on the variable disk as you lower the motor in.

At this point you have to wrestle the motor on and line up the keyway on the variable disk as you lower the motor in.

  • Reaction score 0
  • Comments 0
Bottom view of the variable disk with the spring still compressed via the long screws I installed.

Bottom view of the variable disk with the spring still compressed via the long screws I installed.

  • Reaction score 0
  • Comments 0
The variable disk must be set in place inside the belt housing before installing the motor.

The variable disk must be set in place inside the belt housing before installing the motor.

  • Reaction score 0
  • Comments 0
View of the installed fixed motor pulley.

View of the installed fixed motor pulley.

  • Reaction score 0
  • Comments 0
The rear of the fixed motor pulley has a set screw that must be tightened. This keeps the pulley in place along with the pinned key.

The rear of the fixed motor pulley has a set screw that must be tightened. This keeps the pulley in place along with the pinned key.

  • Reaction score 0
  • Comments 0
This is the key for the fixed motor pulley. It's tapered and has a pin for the pictured "pin hole" that keeps in in place on the shaft.

This is the key for the fixed motor pulley. It's tapered and has a pin for the pictured "pin hole" that keeps in in place on the shaft.

  • Reaction score 0
  • Comments 0
The fixed motor pulley with it's key at the top of the picture.

The fixed motor pulley with it's key at the top of the picture.

  • Reaction score 0
  • Comments 0
Next the motor fixed pulley and the variable pulley are to be installed. The variable disk on the right has been rebuilt/

Next the motor fixed pulley and the variable pulley are to be installed. The variable disk on the right has been rebuilt/

  • Reaction score 0
  • Comments 0
A shot of the motor plate for my 2hp 3 phase.

A shot of the motor plate for my 2hp 3 phase.

  • Reaction score 0
  • Comments 0
expressline99

Bridgeport Series 1 VS 2hp Motor Tear Down and Bearing replacement

Bridgeport Series 1 VS 2hp Motor Tear Down and Bearing replacement
Click to expand...

Album information

Album owner
expressline99
Date created
Item count
73
View count
7,683
Comment count
0
Rating
0.00 star(s) 0 ratings

Album privacy

expressline99

expressline99

Media items
1,002
Albums
19
Can view media items
Everyone
Can add media items
Album owner only

Share this album

Back
Top