Media added by expressline99

There was a slight slope from the truck to the stand. Roughly 6" of drop. These are the rails I attached to the ledge I put on the stand.

There was a slight slope from the truck to the stand. Roughly 6" of drop. These are the rails I attached to the ledge I put on the stand.

  • 0
  • 0
I added a ledge for the rails to sit on directly to the shipping pallet the surface plate was on.

I added a ledge for the rails to sit on directly to the shipping pallet the surface plate was on.

  • 0
  • 0
This is where I got the idea of where I could put rails to slide it on. So it needed a cleat. See next pictures

This is where I got the idea of where I could put rails to slide it on. So it needed a cleat. See next pictures

  • 0
  • 0
Just another angle of the garage from where I was moving the plate...

Just another angle of the garage from where I was moving the plate...

  • 0
  • 0
I had the plate on it's shipping pallet... plus One more pallet that I had in the warehouse.

I had the plate on it's shipping pallet... plus One more pallet that I had in the warehouse.

  • 0
  • 0
What I had to do.

What I had to do.

  • 0
  • 0
This little girl appeared inbetween pictures. Really wanted to be in the pictures!

This little girl appeared inbetween pictures. Really wanted to be in the pictures!

  • 1
  • 1
This little girl appeared inbetween pictures. Really wanted to be in the pictures!

This little girl appeared inbetween pictures. Really wanted to be in the pictures!

  • 0
  • 0
Painted 2nd view.

Painted 2nd view.

  • 0
  • 0
Painted!

Painted!

  • 0
  • 0
Picture of the simpson strong-tie bearing plate 2"x2" 5/8" hole

Picture of the simpson strong-tie bearing plate 2"x2" 5/8" hole

  • 0
  • 0
Close up of the leveling feet.

Close up of the leveling feet.

  • 0
  • 0
The bottom leveling feet.

The bottom leveling feet.

  • 0
  • 0
Franken corners. These were made to be removeable corner brackets for the plate.

Franken corners. These were made to be removeable corner brackets for the plate.

  • 0
  • 0
I added 4 "attachment" points to the 4 corners of the stand.

I added 4 "attachment" points to the 4 corners of the stand.

  • 0
  • 0
The base of the stand

The base of the stand

  • 0
  • 0
Close up of the 3 point mounting system.

Close up of the 3 point mounting system.

  • 0
  • 0
The stand has a 3 point bessel leveling setup. These points are exactly as the manufacture requires.

The stand has a 3 point bessel leveling setup. These points are exactly as the manufacture requires.

  • 0
  • 0
Overall view of stand

Overall view of stand

  • 0
  • 0
A view of the spindle speed change plate installed.

A view of the spindle speed change plate installed.

  • 0
  • 0
The two mounting holes for the speed change face plate.

The two mounting holes for the speed change face plate.

  • 0
  • 0
After the two screws are installed that hold the speed change assembly on the belt housing.

After the two screws are installed that hold the speed change assembly on the belt housing.

  • 0
  • 0
The speed change assembly is held on the belt housing by two socket head screws that go here.

The speed change assembly is held on the belt housing by two socket head screws that go here.

  • 0
  • 0
The spindle speed change plate. The long screws hold the speed change assembly on to the belt housing. The little screws hold the face plate on.

The spindle speed change plate. The long screws hold the speed change assembly on to the belt housing. The little screws hold the face plate on.

  • 0
  • 0
Back
Top