Tighten the set screw down and the new brake handle is installed!

Tighten the set screw down and the new brake handle is installed!

  • Reaction score 0
  • Comments 0
Insert the dowel pin... this was fun you have to fiddle with it to get it in place...

Insert the dowel pin... this was fun you have to fiddle with it to get it in place...

  • Reaction score 0
  • Comments 0
This is how the handle should be oriented when installed.

This is how the handle should be oriented when installed.

  • Reaction score 0
  • Comments 0
The dowel pin for the handle.

The dowel pin for the handle.

  • Reaction score 0
  • Comments 0
There is where the set screw holds the pin in place...this faces out. Seems obvious but anyway. :)

There is where the set screw holds the pin in place...this faces out. Seems obvious but anyway. :)

  • Reaction score 0
  • Comments 0
Spindle brake handle with pin and set screw.

Spindle brake handle with pin and set screw.

  • Reaction score 0
  • Comments 0
Showing Mounting Holes For Spindle Pulley Hub

Showing Mounting Holes For Spindle Pulley Hub

  • Reaction score 0
  • Comments 0
Now put the new drive belt on. Secure it with a zip tie to keep it on and out of the way.

Now put the new drive belt on. Secure it with a zip tie to keep it on and out of the way.

  • Reaction score 0
  • Comments 0
Lower view of the top spindle pulley hub bearing sitting directly on the snap ring.

Lower view of the top spindle pulley hub bearing sitting directly on the snap ring.

  • Reaction score 0
  • Comments 0
A new bearing (6007 double sealed) should be installed on top of the spindle pulley hub. After installed.

A new bearing (6007 double sealed) should be installed on top of the spindle pulley hub. After installed.

  • Reaction score 0
  • Comments 0
A new bearing (6007 double sealed) should be installed on top of the spindle pulley hub.

A new bearing (6007 double sealed) should be installed on top of the spindle pulley hub.

  • Reaction score 0
  • Comments 0
Brake bearing cap. This is just to show those two screws that hold the brake bearing cap to the lower belt housing.

Brake bearing cap. This is just to show those two screws that hold the brake bearing cap to the lower belt housing.

  • Reaction score 0
  • Comments 0
View two after installing the spindle pulley hub assembly.

View two after installing the spindle pulley hub assembly.

  • Reaction score 0
  • Comments 0
View one after installing the spindle pulley hub assembly.

View one after installing the spindle pulley hub assembly.

  • Reaction score 0
  • Comments 0
There is a flat on the brake bearing cap (I messed up the picture it was on the other side)

There is a flat on the brake bearing cap (I messed up the picture it was on the other side)

  • Reaction score 0
  • Comments 0
After sliding the bearing slidding housing on to the splindle gear hub. Yuo must fix it iplace using a snap ring.

After sliding the bearing slidding housing on to the splindle gear hub. Yuo must fix it iplace using a snap ring.

  • Reaction score 0
  • Comments 0
at this point the svari-disc hub can be installed on the spildle pulley hub..

at this point the svari-disc hub can be installed on the spildle pulley hub..

  • Reaction score 0
  • Comments 0
Different angle of the hub being installed.

Different angle of the hub being installed.

  • Reaction score 0
  • Comments 0
This is after the bearing sliding housing is installed.

This is after the bearing sliding housing is installed.

  • Reaction score 0
  • Comments 0
After installing a new bearing into the Bearing sliding housing it's time to install it. Simply press it into place on the Vari-disc hub.

After installing a new bearing into the Bearing sliding housing it's time to install it. Simply press it into place on the Vari-disc hub.

  • Reaction score 0
  • Comments 0
Install the snap ring like this. This will help keep the Key from coming out if it loosens up. Mine was lodged elsewhere in the gear housing.

Install the snap ring like this. This will help keep the Key from coming out if it loosens up. Mine was lodged elsewhere in the gear housing.

  • Reaction score 0
  • Comments 0
Install the snap ring on the spindle pulley hub.

Install the snap ring on the spindle pulley hub.

  • Reaction score 0
  • Comments 0
Snap ring that holds the stationary vari-disc pulley in place.

Snap ring that holds the stationary vari-disc pulley in place.

  • Reaction score 0
  • Comments 0
Press the spindle pulley hub into the stationary vari-disc pulley.

Press the spindle pulley hub into the stationary vari-disc pulley.

  • Reaction score 0
  • Comments 0
expressline99

Bridgeport Series 1 VS 2hp belt housing tear down and rebuild

Bridgeport Series 1 VS 2hp belt housing tear down and rebuild
Click to expand...

Album information

Album owner
expressline99
Date created
Item count
115
View count
8,256
Comment count
0
Rating
0.00 star(s) 0 ratings

Album privacy

expressline99

expressline99

Media items
1,002
Albums
19
Can view media items
Everyone
Can add media items
Album owner only

Share this album

Back
Top